湖州水溶性单工位射蜡机(12T)
设备名称：水溶性单工位湖州射蜡机(12T)
设备编号：TQ-8010
设备简介：
1.射蜡机操作系统简单明了，所有参数设置匀为数字式 2.二段温度控制蜡温
3.射蜡压力为三段压力，解决产品凹陷问题
4.蜡桶储蜡量大为120L
5.蜡桶配有超温脱扣开关，防止超温引发火灾。
1.The operation system of wax injection machine is simple and clear,and all parameters are uniformly set to digital
2.Second stage temperature control wax temperature
3.The wax injection pressure is a three-stage pressure to solve the problem of product depression
4.The wax storage capacity of wax bucket is 120L
5.The wax bucket is equipped with an overtemperature trip switch to prevent overtemperature from causing fire.
参数配置：
基本参数 | ||
置模部分 Mold setting part | 合模压力Clamping pressure | 12T |
合模缸径Mold closing cylinder diameter | φ125 | |
压板尺寸Pressing plate size | 470*590*43(mm) | |
置模下板尺寸Dimension of lower plate for mold setting | 470*590*50(mm) | |
合模行程Clamping stroke | ST400mm | |
最大开距Maximum opening distance | 400mm | |
最小开距Minimum opening distance | 80mm | |
置模宽度Mold setting width | 450mm | |
置模深度Mold setting depth | 350mm | |
液压部分 Hydraulic part | 液压泵流量及压力Flow and pressure of hydraulic pump | 40L/140KG |
液压电机Hydraulic motor | 3.75KW | |
液压油型号Hydraulic oil model | 68# | |
电磁阀Solenoid valve | 台湾/Taiwan | |
油泵0il pump | 台湾/Taiwan | |
射蜡部分 Wax injection part | 挤蜡动作Wax squeezing action | 二段式Two-stage type |
挤蜡压力Wax extrusion pressure | 5~60KG | |
一次最大射蜡量Maximum wax injection amount at one time | 4.5L | |
射蜡流量Wax injection flow | 0-0.5L/S | |
储蜡桶容积Volume of wax storage barrel | 120L | |
储蜡桶加热功率Heating power of wax storage barrel | 2*2KW(4KW) | |
储蜡桶加蜡方式Wax filling method of wax storage barrel | 手动/自动Manual/Automatic | |
射嘴孔径Nozzle aperture | φ6.8mm | |
| 正/负0.1℃Positive/negative 0.1℃ | |
挤蜡油缸缸径Cylinder diameter of wax squeeze cylinder | φ125mm | |
挤蜡油缸轴径Diameter of wax squeeze cylinder shaft | φ60mm | |
挤蜡缸活塞直径Diameter of wax squeeze cylinder piston | φ125mm | |
挤蜡缸缸径Diameter of wax squeeze cylinder | φ125mm | |
射嘴上下调整距离Up and down adjustment distance of nozzle | 250mm | |
射嘴进退调整距离Adjustment distance of nozzle advance and retreat | 230mm | |
射嘴左右调整距离Left and right adjustment distance of nozzle | 200mm | |
射嘴到压板中心距Center distance from nozzle to pressing plate | 最短Minimum50mm | |
